Kay Pee Corporation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• Industrial Automation

• UPS Systems

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)

• Inverter-Duty Design: Designed to handle harmonics, switching surges, and thermal stress caused by inverter or VFD operations.

• Thermal Withstand: Designed for higher temperature rise with better insulation and oil cooling.

• Low Noise & Vibration: Constructed to minimize acoustic noise and withstand mechanical stresses from inverter switching.

• Tap Changer (OCTC): Manual tap adjustment for voltage regulation, must be operated when transformer is off.

• Protection: Equipped with Buchholz relay, oil temperature indicator, winding temperature indicator, and pressure relief valve.

• Solar Power Plants (Inverter Interfacing)

• Wind Turbine Systems

• Variable Frequency Drive Systems

• UPS Systems

• Industrial Automation

This is an inverter-duty oil-immersed transformer specifically designed to operate on the input side or output side of power electronic equipment such as Variable Frequency Drives (VFDs), inverters, or solar power systems. It steps down voltage from 11 kV (primary) to 0.8 kV (secondary) and is cooled using transformer oil to ensure efficient heat dissipation and long service life.

The transformer is equipped with an Off-Circuit Tap Changer (OCTC) on the high-voltage (11 kV) side, allowing for manual voltage adjustment when the transformer is de-energized. This helps in maintaining output voltage within the desired range under varying grid or load conditions.

• Type: Oil-Immersed, Inverter Duty

• Cooling: ONAN (Oil Natural Air Natural)

• Rated Voltage:

  • Primary (HV): 11 kV

  • Secondary (LV): 0.8 kV

• Tapping Range: ±5% in 2.5% steps (typical), via Off-Circuit Tap Changer

• Frequency: 50 Hz / 60 Hz (as per requirement)

• Insulation Class: Class A or F

• Duty: Suitable for non-sinusoidal loads, high harmonic content

• Vector Group: Often Dyn11 or customized based on inverter system needs

• Impedance: As per application (e.g., 4% to 6% typical)