Kay Pee Corporation
Kay Pee Corporation
Kim, Surat, Gujarat
GST No. 24ABLPP4508N1Z9
TrustSEAL Verified
Call 0804764383076% Response Rate
SEND EMAIL

Oil Cooled Distribution Transformer 11111

 

 

Distribution Transformer Is An Electrical Isolation Transformer Which Convert Higher Voltage Electricity To Lower Voltage Levels Acceptable For Use In Homes & Industries. A Distribution Transformer's Function Is Straight Forward : To Step Down The Voltage & Provide Isolation Between Primary & Secondary. Electrical Energy Is Passed Through Distribution Transformers To Reduce High Distribution Voltage Levels Down To End Use Levels. Nearly All Energy Passes Through At Least One Distribution Transformer Before Being Consumed By An End Use Appliance , Motor Or Other Piece Of Equipment. Distribution Transformers Are Found In All Sectors Of The Economy : Residential , Commercial & Industrial.


Distribution Transformers Are Generally Categorized In Several Ways :

  • Type Of Insulation : Liquid Immersed OR Dry Type
  • Number Of Phases : Single Phase OR Three Phase
  • Voltage Level (For Dry Type) : Low OR Medium

 

 

 

 

Distribution Transformer Is An Electrical Isolation Transformer Which Convert Higher Voltage Electricity To Lower Voltage Levels Acceptable For Use In Homes & Industries. A Distribution Transformer's Function Is Straight Forward : To Step Down The Voltage & Provide Isolation Between Primary & Secondary. Electrical Energy Is Passed Through Distribution Transformers To Reduce High Distribution Voltage Levels Down To End Use Levels. Nearly All Energy Passes Through At Least One Distribution Transformer Before Being Consumed By An End Use Appliance , Motor Or Other Piece Of Equipment. Distribution Transformers Are Found In All Sectors Of The Economy : Residential , Commercial & Industrial.


Distribution Transformers Are Generally Categorized In Several Ways :

  • Type Of Insulation : Liquid Immersed OR Dry Type
  • Number Of Phases : Single Phase OR Three Phase
  • Voltage Level (For Dry Type) : Low OR Medium

 

 

 

 

Distribution Transformer Is An Electrical Isolation Transformer Which Convert Higher Voltage Electricity To Lower Voltage Levels Acceptable For Use In Homes & Industries. A Distribution Transformer's Function Is Straight Forward : To Step Down The Voltage & Provide Isolation Between Primary & Secondary. Electrical Energy Is Passed Through Distribution Transformers To Reduce High Distribution Voltage Levels Down To End Use Levels. Nearly All Energy Passes Through At Least One Distribution Transformer Before Being Consumed By An End Use Appliance , Motor Or Other Piece Of Equipment. Distribution Transformers Are Found In All Sectors Of The Economy : Residential , Commercial & Industrial.


Distribution Transformers Are Generally Categorized In Several Ways :

  • Type Of Insulation : Liquid Immersed OR Dry Type
  • Number Of Phases : Single Phase OR Three Phase
  • Voltage Level (For Dry Type) : Low OR Medium

 

 

Power & Distribution Transformer

Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
  • Power & Distribution Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price
Product Brochure

Product Details:

PhaseThree Phase
BrandKAY PEE
Input Voltage11 KV & 22 KV & 33 KV (As Per Customer's Demand)
Output Voltage0.433 KV (As Per Customer's Demand)
Frequency50 HZ
Winding MaterialE. C. Grade D. P. C. Copper Wire & Strips
Class Of InsulationA
No Of PhaseThree
Orientation Of HV and LV180 Degree (As Per Customer's Demand)
Temprature Rise Oil and Winding40 DegreeC (In Oil) & 45 DegreeC (In Winding)
Load Losses At Half LoadAs Per BIS Level
No Load LossesAs Per Customer's Demand
TapingAs Per Customer's Demand
Full Load LossesAs Per BIS Level
Vector GroupeAs Per Customer's Demand
Type Of CoolingOil Cooled
No load CurrentLess Than 2 % Of Full Load Current
ImpedanceAs Per BIS
Rated CapacityAs Per Customer's Demand
InstallatonIndoor / Outdoor

Request
Callback
Yes! I am Interested

Three Phase Distribution Transformer

Three Phase Distribution Transformer
  • Three Phase Distribution Transformer
  • Three Phase Distribution Transformer
  • Three Phase Distribution Transformer
  • Three Phase Distribution Transformer
  • Three Phase Distribution Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / UnitGet Latest Price
Product Brochure

Product Details:

Supply Frequency50 / 60 Hz
No Of PhaseThree
Nominal Voltage11 KV / 22 KV / 33 KV
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
Temprature Rise Oil And Winding50 / 55 Degree
ImpedanceAs Per BIS
No Load LossesAs Per Costumer Requirement
Type Of CoolingOil Cooled
Phase GroupAs Per vector group
Installationindoor / Outdoor
No Load CurrentLess Then 3 Percentage
Rated KVAAs costumer requirement(250 KVA To 2500 KVA)
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
TappingAs Per Costumer Requirement( Generally +5% To -5%)
Full Load LossesAs per BIS Lavel
Load Loss At Half LoadAs Per BIS Lavel

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings : 
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
 The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator : 
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
 for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test. 

Request
Callback
Yes! I am Interested

High tension Transformers

High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
  • High tension Transformers
Get Best Quote
Approx. Price: Rs 6.75 Lakh / OnwordGet Latest Price
Product Brochure

Product Details:

Minimum Order Quantity1 Onword
MaterialCopper
No Of PhaseThree
Type Of CoolingOil Cooled
percentage ImpedanceAs Per BIS
Load Losses At half LoadAs per BIS lavel
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
InstalatonIndoor / Outdoor
Temprature rise Oil And Winding40 / 45 degree
No Load currentLess then 3 Percent of Full load current
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
TapingAs Per Costumer Requirement( Generally +5% To -5%)
Full load lossesAs Per BIS Lavel
Rated KVA250 KVA
Nominal Voltage11 KV / 22 KV / 33 KV
Phase GroupAs Per vector group
No Load LossesAs Per Costumer Requirement

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings : 
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
 The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator : 
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
 for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test. 


Request
Callback


Additional Information:

  • Item Code: KP-01-BIS-OCTC
  • Production Capacity: 10 Pcs Per Mounth
  • Delivery Time: 30 Days
  • Packaging Details: NA
Yes! I am Interested

1000 Kva Oil Cooled Distribution Transformer

1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
  • 1000 Kva Oil Cooled Distribution Transformer
Get Best Quote
Approx. Price: Rs 18 Lakh / PieceGet Latest Price
Product Brochure

Product Details:

Minimum Order Quantity1 Piece
Power Rating1MVA
Cooling TypeONAN
Number of Phase3-Phase
Voltage Ratio11kV/433V
Short circuit impedance5.00 %
BrandKay Pee
Manufactured ByKay Pee
Energy Efficiency Level1
Reference StandardIS 1180
Insulation ClassA
AMC AvailableYes
Onsite Support AvailableYes
Winding MaterialCopper
Winding TurnsStep-Down
StandardsIS-1180
Country of OriginMade in India

Request
Callback


Additional Information:

  • Item Code: KP-07-BIS-OCTC
  • Production Capacity: 10 PCS Per Month
  • Delivery Time: 30 Days
  • Packaging Details: NA
Yes! I am Interested

High Voltage Transformer

High Voltage Transformer
  • High Voltage Transformer
  • High Voltage Transformer
Get Best Quote
Approx. Price: Rs 14 Lakh / PieceGet Latest Price
Product Brochure

Product Details:

Full Load LossesAs per BIS Lavel
Load Losses At Half LoadAs Per BIS Lavel
No Of PhaseThree
Type Of CoolingOil Cooled
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
Rated KVAAs costumer requirement(250 KVA To 2500 KVA)
TapingAs Per Costumer Requirement( Generally +5% To -5%)
No Load CurrentLess Then 3 Percentage
InstalatonIndoor / Outdoor
Vector GroupAs Per Costumer Requirement
Temprature rise Oil And Winding50 / 55 degree
ImpedanceAs Per BIS
No Load LossesAs Per Costumer Requirement
Nominal Voltage11 KV / 22 KV / 33 KV
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As per customer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.

 

Request
Callback
Yes! I am Interested

Step Up Distribution Transformer

Step Up Distribution Transformer
  • Step Up Distribution Transformer
  • Step Up Distribution Transformer
  • Step Up Distribution Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

Vector GroupAs Per Costumer Requirement
StandardIS 1180
InstalatonIndoor / Outdoor
Load Losses At Half LoadAs Per BIS Lavel
Full Load LossesAs per BIS Lavel
No Of PhaseThree
Type Of Cooling Oil Cooled
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
No Load LossesAs Per Costumer Requirement
Nominal Voltage11 KV / 22 KV / 33 KV
TapingAs Per Costumer Requirement( Generally +5% To -5%)
ImpedanceAs Per BIS
No load CurrentLess Then 3 Percentage
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
Temprature rise Oil And Winding50/55 degree
Rated KVAKVA Capacity As Per requirement (250 KVA To 2500 KVA)

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As percustomer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.


Request
Callback
Yes! I am Interested

250kVA Three Phase ONAN Distribution Transformer

250kVA Three Phase ONAN Distribution Transformer
  • 250kVA Three Phase ONAN Distribution Transformer
  • 250kVA Three Phase ONAN Distribution Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

Power Rating250kVA
Voltage Ratio11kV/433V
Cooling TypeONAN
Number of PhaseThree Phase
Winding MaterialCopper
StandardsIS-1180
Supply Frequency50Hz

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 


The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminium /copper conductor/ foil.


Request
Callback
Yes! I am Interested

OCTC Three Phase Distribution Transformer

OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
  • OCTC Three Phase Distribution Transformer
Get Best Quote
Approx. Price: Rs 6 Lakh / PieceGet Latest Price

Product Details:

KVAAs per costumer Requirement (250 KVA To 2500 KVA
ImpedanceAs Per BIS
No Load LossesAs Per Costumer Requirement
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
TapingAs Per Costumer Requirement( Generally +5% To -5%)
Type Of CoolingOil Cooled
Installationindoor / Outdoor
Phase GroupAs Per vector group
No Load currentLess then 3 Percent of Full load current
Full load lossesAs Per BIS Lavel
Nominal Voltage11 KV / 22 KV / 33 KV
No Of PhaseThree
No Load Losses at Half LoadAs per BIS Lavel

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As percustomer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.

Request
Callback
Yes! I am Interested

High Power Transformer

High Power Transformer
  • High Power Transformer
  • High Power Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

Type Of CoolingAir cooled / Oil Cooled
Vector GroupAs Per Costumer Requirement
TapingAs Per Costumer Requirement
No Load LossesAs Per Costumer Requirement
Nominal Voltage11 KV / 22 KV / 33 KV
LV Voltage0.433 KV
Load Losses At Half LoadAs Per BIS Lavel
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
Temprature rise Oil And Winding50 / 55 degree
Rated KVAKVA Capacity As Per requirement
ImpedanceAs Per BIS
Full Load LossesAs per BIS Lavel
Service and DutyContinuous
No Of PhaseThree
InstalatonIndoor / Outdoor

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As per customer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.

Request
Callback
Yes! I am Interested

Oil Filled Transformer

Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
  • Oil Filled Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

No Load LossesAs Per Costumer Requirement
Load Losses At Half LoadAs Per BIS Lavel
Nominal Voltage11 KV / 22 KV / 33 KV
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
Rated KVAAs costumer requirement(250 KVA To 2500 KVA)
ImpedanceAs Per BIS
Full Load LossesAs per BIS Lavel
No Of PhaseThree
Temprature rise Oil And Winding50 / 55 degree
TapingAs Per Costumer Requirement( Generally +5% To -5%)
InstallatonIndoor / Outdoor
Type Of CoolingOil Cooled
Vector GroupAs Per Costumer Requirement

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings : 
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
 The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator : 
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
 for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test. 

Request
Callback
Yes! I am Interested

OLTC Three Phase Distribution Transformer

OLTC Three Phase Distribution Transformer
  • OLTC Three Phase Distribution Transformer
  • OLTC Three Phase Distribution Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

InstalatonIndoor / Outdoor
Temprature rise Oil And Winding50 / 55 degree
No Of PhaseThree
Load Losses At Half LoadAs Per BIS Lavel
Rated KVAAs costumer requirement(250 KVA To 2500 KVA)
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
Type Of CoolingOil Cooled
Full Load LossesAs per BIS Lavel
No Load CurrentLess Then 3 Percentage
ImpedanceAs Per BIS
TapingAs Per Costumer Requirement( Generally +5% To -5%)
Phase GroupAs Per vector group
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
No Load LossesAs Per Costumer Requirement
Nominal Voltage11 KV / 22 KV / 33 KV

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings : 
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
 The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator : 
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
 for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test. 

Request
Callback
Yes! I am Interested

Substation Transformers

Substation Transformers
  • Substation Transformers
  • Substation Transformers
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

Rated KVAAs Per costumer requirement(250 KVA To 2500 KVA)
TapingAs Per Costumer Requirement( Generally +5% To -5%)
ImpedanceAs Per BIS
No Load lossesAs Per Costumer Requirement
No load CurrentLess Then 3 Percentage of Full Load current
Temprature rise Oil and Winding50 / 55 degree
Fill Load LossesAs Per BIS Lavel
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
supply Frequency50 / 60 Hz
Type Of CoolingOil Cooled
phase GroupAs per Vector Group
Orientation Of HV And LVGeneral 180 Degree And If Required 90 Degree
No Of PhaseThree
Load Losses At Half LoadAs Per BIS Lavel
Nominal Voltage11 KV / 22 KV / 33 KV
Installationindoor / Outdoor

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers. 

The transformer are manufactured in accordance with IS 2026/1977, IS 1180/2016, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
 The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group 
As per customer’s custom requirement.

Core :
 The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test 
The preliminary core loss test will be conducted before passing to the assembly stage.

Winding : 
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings : 
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
 The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator : 
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
 for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test. 

Request
Callback
Yes! I am Interested

Furnace Transformer

Furnace Transformer
  • Furnace Transformer
  • Furnace Transformer
Get Best Quote
Approx. Price: Rs 3.35 Lakh / PieceGet Latest Price

Product Details:

Nominal Voltage11 KV / 22 KV / 33 KV
Vector GroupAs Per Costumer Required
Temprature Rise Oil And Winding60 / 65 Degree
ImpedanceAs Per Costumer Demand
No load CurrentLess Then 3 Percentage of rated Current
Full Load LossesAs Per IS 2026
No Of PhaseThree
Secondary VoltageAs Per Costumer Requirement (Generally 433 Voltage)
InstallationIndoor / Outdoor
Make" KAY PEE "
Orientatin of HV And LVGeneral 180 degree If required 90 Degree
Supply Frequency50 / 60 Hz
TappingAs Per Costumer Requirement( Generally +5% To -5%)
No Load LossAs Per Costumer Required
KVAAs Per Costumer Requirement ( 10 KVA To 2500 KVA )
Type Of CoolingOil Cooled

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As percustomer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.




Request
Callback
Yes! I am Interested

Auxiliary Transformer

Auxiliary Transformer
  • Auxiliary Transformer
  • Auxiliary Transformer
Get Best Quote
Approx. Price: Rs 35,000 / OnwardGet Latest Price

Product Details:

Nominal Voltage3.3 KV / 6.6 KV / 11 KV / 22 KV / 33 KV
Supply Frequency50 / 60 Hz
Orientation HV and LVGeneral 180 Degree if Required 90 Degree
KVAAs Per Customer Requirement ( 10 KVA To 2500 KVA )
InstallationIndoor / Outdoor
Vector GroupAs Per Customer Required
ImpedanceAs Per Costumer Demand
No Load LossAs Per Costumer Required
No Load CurrentLess Then 3 Percentage of Rated Current
TappingAs Per Costumer Requirement( Generally +5% To -5%)
Make" KAY PEE "
No Of PhaseThree
Type Of CoolingOil Cooled
Temprature Rise Oil and Winding60 / 65 Degree
Full Load LossesAs Per IS 2026
Secondary VoltageAs Per Customer Requirement

KAY PEE offers a complete range of power and distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. KAY PEE 's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Transformers can be used for indoor or outdoor applications and can be provided with off-load and on-load tap changers.

The transformer are manufactured in accordance with IS 2026/1977, IEC 60076 or as per customer’s custom requirement.

The transformers will be suitable for outdoor installation with three phase, 50Hz, 11 kV system in which the neutral is effectively earthed and theyshould be suitable for service with fluctuations in supply voltage up to plus 12.5% to minus 12.5%.


Range :
The standard ratings shall be 250, 315, 400, 500, 630, 800, 1000, 1250, 1500, 1600, 2000 and 2500 KVA for 11 kV distribution transformers.


Vector Group
: As per customer’s custom requirement.

Core :
The core shall be stack / wound type of high grade cold rolled grain oriented annealed steel lamination having low loss and good grain properties, coated with hot oil proof insulation, bolted together and to the frames firmly to prevent vibration or noise.

Core Test
: The preliminary core loss test will be conducted before passing to the assembly stage.

Winding :
HV and LV windings shall be wound from Super Enamel covered /Double Paper covered, aluminum /copper conductor/ foil.

Tapings :
For ratings higher than 250 kVA, tapping shall be provided if required by the purchaser on the higher voltage winding for variation of HV voltage within range of (+) 5.0 % to (-)15.0 % in steps of 2.5%.

OIL :
The insulating oil shall comply with the requirements of IS 335 or BS 148 Oil shall be filtered and tested for break down voltage (BDV) and moisture content before filling. The oil shall be filled under vacuum.

Tank :
The transformer tank is of robust construction rectangular in shape and shall be built up of electrically tested welded mild steel plates of thickness of 6 mm for top and bottom and 4 mm side plate.

Conservator :
The capacity of a conservator tank is designed keeping in Observation the total quantity of oil and its contraction and expansion due to temperature variations The total volume of conservator shall be such as to contain10% quantity of the oil. Normally 3% quantity the oil shall be contained in the conservator.

BUSHINGS:
for 11 kV, 17.5 kV class bushings and for 0.433 kV, 1.1 kV class bushings shall be used.

TESTING : We are conduct all routin test.





Request
Callback
Yes! I am Interested

Step Down Distribution Transformer

Step Down Distribution Transformer
    Ask For Price
    X

    Explore More Products

    View All Products




    Reach Us
    Hirenkumar Chakalasiya (Proprietor)
    Kay Pee Corporation
    Block No. 89, Survey No. 113/2, Village Mota Borsara Kim, Taluka Mangrol
    Surat - 394110, Gujarat, India
    Get Directions


    Call Us


    Send E-mail